220V 2200W DPF High Temperature Regeneration Equipment/DPF Ash Clean Machine

Product Description

Product introduction

Product Name	Electric heating type DPF high temperature regeneration equipment
Main technical parameters
Model	KL-DZL15	KL-DZL40
Power	15 kW	35 kW
Heating rate	30ºC/min	44ºC/min
The chamber size	500×550×700mm	800×800×700mm
Boundary dimension	1050×850×1880mm	1350×1100×1880mm
The substrate capacity	Single loading of a diameter of 330mm or Two DPF carriers with 190mm diameter substrate	A single loading of four diameters of 330mm or Six DPF carriers with 190mm diameter substrate
Power supply	Three-phase five-line system,380V,50Hz
Temperature range	Normal temperature~750 ºC
Temperature control tolerance	±5ºC
Electric control system	Temperature control module,7-inch all-piece touch display
Fresh air system	Fresh air fan supplies oxygen and cooling, and automatically controls the intake volume

 

Product Name	Electric heating type DPF high temperature regeneration equipment
Model	KL-DZL25
The chamber size	500×550×700mm (can meet the package φ 450 outer diameter, length ≤450mm)
Power/air source	380v power supply;  Air source pressure: 0.6 ~ 0.8mpa, air consumption ≤30L, intake interface for φ 12 quick connector
Temperature range	Normal temperature ~ 620ºC, maximum temperature 650ºC
Heating power	24KW, heating rate: 28ºC/min
Stages of temperature control	Set three stage temperature, reach the set value for automatic constant temperature.  Temperature control tolerance: set temperature ±10ºC
DPF cooling	For high temperature DPF cooling, two butterfly valves, inlet and exhaust, are used to open and inhale cold air and discharge hot air for cooling and cooling after the end of insulation
Motor power	High temperature resistant 0.37KW three-phase motor, flow 1100m3/h
Surface treatment	Surface paint treatment
Door quantity	Single door, each side of the door is installed with high strength hinge, strong jacking force, easy to operate.
Insulation material	128kg/m3 high density aluminum silicate thermal insulation cotton, with flame retardant, heat insulation and good thermal insulation performance
Protector	Leakage protection, lack of phase protection, motor overcurrent protection, overtemperature heating protection

 

Product name	Standard DPF purging and testing equipment
Model	KL-DCJ30
Main technical parameters
Power supply	220V,50Hz
Fan	Maximum air volume:1060m3/h;maximum vacuum:5kPa
Boundary dimension	1100×800×1880mm
Blow control	Overall pulse purge, PLC automatic control, purge at the same time, vacuum dust collection
Weighing detection	Weighing table range 30Kg,Weigh accuracy: ± 1g; the data can be recorded
Back pressure detection	PLC controls automatic detection and data can be displayed and recorded
Light detection	A 150w high-brightness LED light source, optical flux: 15,000 lumens
Grey collecting device	Vacuum suction, 5 micron level can be cleaned, replacement of the filter element, drawer type dust collection room
Gas storage tank capacity	Using 30L air storage tank, no need for manual intervention pressure regulation, automatic program control purge
Electric control system	A 7-inch integrated touch display screen, with PLC programming control
protector	Leakage protection, phase absence protection, motor overprotection
Surface treatment	Electrostatic powder baking paint

 

Product name		Fuel heating type DPF high temperature regeneration equipment
Serial number	Project	Unit	Parameter
1	Model	-	KL-DZT30
2	Rated heating power	kW	30
3	Maximum quantity of wind	m3/min	4
4	Maximum wind pressure	kPa	30
5	Temperature control accuracy	ºC	±20
6	Service voltage	V	Single-phase AC220
7	Power load	kW	2.2
8	Fuel tankage	L	10
9	Boundary dimension	mm	1370x690x1210
10	Net weight	kg	200

RFQ
Q:What are your main products?
A:Our main products are diesel engine exhaust after-treatment system(SCR system, DPF system etc.), and parts(Urea Pump,Urea Nozzle,Catalyst Converter, Sensor etc.)  

Q:Do you have after-sale service?
A:"Customer first" is the core principle followed by our company, and it is also the super criteria adhered by our after-sales service staff. We  have established comprehensive after-sales service network. With headquarter in Wuxi, we have branch offices  Shanghai, Beijing, Changchun, Zhengzhou, Guangzhou, Changsha, Xuzhou and authorized service center throughout the country. We also provide 24 hours free hotline for customerswith premium quality and efficient after-sales service.

Q:I wonder if you can provide free samples?
A:Whether the sample is free depends on the content of the sample and can be decided after discussion.

Q:What product certifications do you have?
A:ISO9001, CE, E-Mark, RoHS And TS16949

Q:What is the delivery time of your product?
A:Generally, it is about 1 month. The delivery time depends on the quantity of the order.